Mass wasting Totally Explained

Everything about Mass Wasting totally explained

Mass movement, also known as slope movement, is the geomorphic process by which soil, regolith, and rock move downslope under the force of gravity. Types of mass wasting include creep, slides, flows, topples, and falls, each with their own characteristic features, and take place over timescales from seconds to years. Mass wasting occurs on both terrestrial and submarine slopes, and has been observed on Earth, Mars, and Venus.
   When the gravitational force acting on a slope exceeds its resisting force, slope failure (mass wasting) occurs. The slope material's strength and cohesion and the amount of internal friction between material help maintain the slope's stability and are known collectively as the slope's shear strength. The steepest angle that a cohesionless slope can maintain without losing its stability is known as its angle of repose. When a slope possesses this angle, its shear strength perfectly counterbalances the force of gravity acting upon it.
   Mass wasting may occur at a very slow rate, particularly in areas that are very dry or those areas that receive sufficient rainfall such that vegetation has stabilised the surface. It may also occur at very high speed, such as in rock slides or landslides, with disastrous consequences, both immediate and delayed, for example, resulting from the formation of landslide dams.
   Factors that change the potential of mass wasting include: change in slope angle; weakening of material by weathering; increased water content; changes in vegetation cover; and overloading.

The importance of water in mass wasting

Water can increase or decrease the stability of a slope depending on the amount present. Small amounts of water can strengthen soils because the surface tension of water gives the soil a lot of cohesion. This allows the soil to resist erosion better than if it were dry. If too much water is present the water may act as a lubricant, accelerating the erosion process and resulting in different types of mass wasting (for example mudflows, landslides, etc). A good example of this is to think of a sand castle. Water must be mixed with sand in order for the castle to keep its shape. If too much water is added the sand washes away, if not enough water is added the sand falls and can not keep its shape.

Types of mass movement

Types of mass movement are distinguished based on how the soil, regolith or rock moves downslope as a whole.

Creep

Downhill creep is a long term process. The combination of small movements of soil or rock in different directions over time are directed by gravity gradually downslope. The steeper the slope, the faster the creep. The creep makes trees and other shrubs curve to reach the sun light. These often trigger land slides because the dirt underneath isn't very strong. The trees most of the time die out because of lack of water and sun, and these rarely happen in wet climates. Caused by freezing then thawing, or hot then cold temperature, it causes surface soils to move up then down, inching its way towards the bottom of the slope. This happens at a rate that isn't noticeable to the naked eye. and it also happens in the tropical regions.

Landslides

Where the mass movement has a well-defined zone or plane of sliding, it's called a landslide. This includes rock slides, slumps and sturzstroms.
It is also one of the common classification of mass wasting.

Flows

Movement of soil and regolith that more resembles fluid behavior is called a flow. These include avalanches, mudflows, debris flows, earth flow, solifluction, lahars and sturzstroms. Water, air and ice are often involved in enabling fluidlike motion of the material.

Topples

Topples are instances when blocks of rock pivot and fall away from a slope.

Falls

A fall, including rockfall, is where regolith cascades down a slope, but isn't of sufficient volume or viscosity to behave as a flow. Falls are promoted in rocks which are characterised by presence of vertical cracks. Falls are a result of undercutting of water as well as undercutting of waves. They usually occur at very steep slopes such as a cliff face. The rock material may be loosened by earthquakes, rain, plant-root wedging, expanding ice, among other things. The accumulation of rock material that has fallen resides at the base of the structure and is know as talus....

Triggers of mass wasting

Soil and regolith remain on a hillslope only while the gravitational forces are unable to overcome the frictional forces keeping the material in place (see Slope stability). Factors that reduce the frictional resistance relative to the downslope forces, and thus initiate slope movement, can include:

seismic shaking
increased overburden from structures
increased soil moisture
reduction of roots holding the soil to bedrock
undercutting of the slope by excavation or erosion
weathering by frost heave
bioturbation

Further Information

Get more info on 'Mass Wasting'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://mass_wasting.totallyexplained.com">Mass wasting Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.